VX 2015 065 Building CATV Amplifier 1,2 GHz
Category : Distribution amplifier Value Line
The VX 2015 is a location feeding in-house amplifier with a frequency range up to 1.2 GHz. It has an active output and a measuring socket on the input and output. Diplex filter and return path amplifier are grouped together on a module (VX201-xxx) and available in the versions 65 MHz, 85 MHz and 204 MHz. All settings are done without interruption with Q-step switch or jumper. In addition, a high pass filter XE-xx can be plugged in the return path to influence the ingress influences.
- High output level up to 1.2 GHz, with low power consumption
- Active single output
- Measuring socket for input and output
- All settings (gain, slope etc.) by rotary switch and Jumper
- Diplex filters, return amplifier pluggable on one module
- Optional - receiver according to EN 60728-14 for ICS-settings
- Optional - pluggable high pass filter at the return path channel
- Low power input <6 W
TECHNICAL DATA
Downstream |
|
Frequency range | 85...1218 MHz |
Gain | 15 dB (± 0,7 dB) |
Ripple | ≤ ±0,8 dB |
Noise figure | <7,0 dB @ 1 GHz, <8,0 dB @ 1,2 GHz |
Output level | 101 dBµV (CENELEC 41 Ch. (CSO/CTB ≥ 60 dB), flat) |
Output level | 100 dBµV (110 Ch/QAM 256, flat, BER <1 E-9) |
Output level | 100 dBµV (all QAM (138 x 256 QAM), EN60728-3-1, flat) |
Input cable simulator | 0/5/10 dB (Jumper) |
Input attenuator | 0...15 dB (Rotary switch 15 Steps) |
Step size | 1 dB |
Input equalizer | 0...30 dB / 1218 MHz Drehpunkt (Rotary switch 15 Steps) |
Step size | 2 dB |
Interstage equalizer (Slope) | 0/2/4 dB (Jumper) |
Test point | -20 dB |
Upstream |
|
Frequency range | 5...65 MHz |
High pass filter pluggable (optional) | 15 MHz (WISI - XE04/0150) |
Gain | 21 dB (± 0,7 dB) |
Ripple | ±0,5 dB |
Noise figure | <8,5 dB |
Output level | 110 dBµV (6 x 256 QAM) |
Interstage attenuator | 0...15 dB (Rotary switch 15 Steps) |
Step size | 1 dB |
Interstage equalizer | 0/2/4/6/8 dB (Jumper) |
Output attenuator | 0/10 dB (Jumper) |
Output equalizer | 0/6 dB (Jumper) |
Ingress control switch (optional) | nach ICS EN 60728-14 |
Test point | -20 dB |
General data |
|
RF connectors | F |
Impedance | 75 Ω |
In/Output return loss | 5...40 MHZ >16, >40MHz -1,5dB Oktave, >12 |
Supply voltage | 230 V AC ±10 % |
Power consumption | <6 W |
Ambient temperature | -20...+55 °C |
Protection class | IP 20 |
EMC | EN50083-2 |
Surge protection RF Ports | 2 kV (1,2/50 μs pulse EN61000-4-5) |
Dimensions W x H x D | 163 x 90 x 50 mm |